It's worth pointing out that there are actually two main types of PCMCIA memory cards. The most common by far are the ATA cards mentioned here, which are basically CF cards in a different form factor (equivalent to a CF card in a CF-to-PCMCIA adapter) and work by emulating either an IDE hard drive or an ISA IDE controller depending on wiring. While uncommon at this point, CF controller chips are still available and some specialized suppliers do manufacture these cards brand new using modern NAND flash.
The much more problematic ones to find a replacement for in 2026 are the so-called "linear" memory-mapped cards, consisting of one or more banks of raw parallel NOR flash with no controller IC. Linear cards were never standardized and the protocol used to interface to parallel flash can vary greatly across chip families, so the vast majority of devices that use them are hardcoded to only accept cards with a specific manufacturer and device ID. Many NOR flash manufacturers from the turn of the century have long discontinued their products and emulating parallel flash using modern FPGAs and microcontrollers is also non-trivial due to their memory-mapped nature, so owners of legacy telecom equipment and original Dance Dance Revolution arcade cabinets [1] are left with pretty much no viable replacement option once the stock cards fail.
[1] https://psx-spx.consoledev.net/konamisystem573/#flash-chips-...
HN headline is wrong/misleading.
This is more of a survey to identify _potential_ suppliers of NEW CF/PC memory cards. It's not a request for bids, nor asking civilians to root around their junk drawers for cards to send off to the military.
Reading between the lines, they are likely evaluating multiple options for modernizing whatever F-22 system this is, and need to find out if going this route is even feasible.
For anyone wondering what these are used for:
All current US military aircraft (at least up through the F-35) use CF cards to take mission planning from the laptops in the SCIF (or whatever unclass space they are using) to the aircraft.
As an aside, LCACs (among other platforms) also use these systems and cards. So this is a pretty widespread use case.
Bought a few CF cards from Dogfish SSD (https://dogfishssd.com/) sometime ago. They are readily available on Amazon and can be bought with relatively no fuss. The company are NOT based out of the US though.
The company that I do recommend for any industrial flash is Delkin Devices (https://www.delkindevices.com/). They are based out of San Diego, CA and I bought USB 3.0 high endurance drives from them and so far the performance of those have been solid, and it's lasted me many cycles. These are whom you'd be in contact with, for bids like these.
It's worth expanding the supply chain options locally. If anyone needs this they'd have to get Micron or Sandisk to make and assemble them into other form factors. This part is what is harder than it looks, and would need to be done.
As a bit of a fun aside, Industrial CF cards are a popular stand-in for hard disks in vintage computers (since in IDE mode they can be adapted passively to IDE - they're both parallel ATA but with different pinouts). Too bad they don't make hard drive noises, though.
"[...] The PC or CF card must have a storage capacity of 256 megabytes (MB) or greater [...]" I'm guessing they have some system that bootstraps off of PC cards, or stores some small amount of low-bandwidth essential things. It's interesting that it's cheaper to req. a bunch of cards & adapters than it is to retrofit & modernize. Well, I suppose that's not that surprising, if I stop to think about it; from a systems integration point it's certainly way more reliable and less risky to replace a like part for a like part, rather than redesigning the hardware to use a more modern flash storage device.
China again is the gate to the bridge from 20th to 21st century. We don't have them because we never even tried to secure the supply chain beyond the bare minimum.
Oh my Singaporean friend Alice told me I should contact them, she has a supplier but if she does the deal through my US company it'll be a lot easier!
SanDisk makes them, I bought some a few years back.
Why not use SD to CF converter adapters?
One extra layer, but the chips are commodity.
With glue, should be able to meet environmentals, shock and vibe etc
"Old" I think you mean new...
[flagged]
Cool coincidence. In a past job, I specifically made replacement PCMCIA cards for these (and other) planes. Instead of making cards with a controller and onboard storage, we made cards with an FPGA/microcontroller and a microSD card soldered to the PCB. We did this specifically because these aircraft use (at least partially) broken implementations of the PCMCIA protocol, and we'd update the bus protocol per aircraft to work around the limitations. None of these planes can just go buy stuff off the street because some large portion just doesn't work because their protocol isn't fully implemented and isn't flexible to deal with variance in timing/speed/etc.
A fun story: Our cards had whatever industrial-spec microSD card we could find (16GB, 32GB, etc.), and we'd internally limit the disk size to whatever the platform needed. Almost every aircraft had some specific number of MB they wanted because all of their CONOPS listed it, and they didn't want to update documentation or software to put a different number there. We had a plane that could only use EXACTLY 128MB, but they were currently using 256MB cards and partitioning them to 128MB. We updated the disk size to present as 128MB so they could skip this step, and they specifically told us to put it back to 256MB because they didn't want to update the commissioning process to remove the partitioning step.
It was rewarding work, and the card we designed was cheap (~$500 each, which is literally nothing for major platforms like this) and 100% US-designed and made (with the exception of ICs manufactured in the usual places). Still, the procedural and cultural practices of these program offices made it a real struggle to get traction and deploy them widely. Government acquisition is just generally designed around funding primes for current development and then paying through the nose for sustainment later. It was hard to design something for widespread sustainment use because by the time you were done and ready for production, a bunch of parts would be obsolete. Then you'd have to rev the design over and over. We were never allowed to stockpile anything, even if it was trivially cheap, to facilitate production later.